Heat transfer enhancement of impinging jet on flat surface - A comprehensive review
Article Sidebar
Main Article Content
Abstract
High-heat transfer of jet impingement for cooling and heating processes becomes more important in engineering applications such as drying processes of paper and textiles, electronic components cooling, freezing of tissue, gas turbine blades cooling, refrigeration unit, and solar collectors, etc. The comprehensive review of heat transfer intensification of jet impingement using non-swirling and swirling jets is reported in the present paper. In addition, heat transfer uniformity characteristics on surfaces of various swirling impinging jets are presented.
Article Details
Copyright @2021 Engineering Transactions
Faculty of Engineering and Technology
Mahanakorn University of Technology
References
D.W. Colucci and R. Viskanta, “Effect of nozzle geometry on local convective heat transfer to a confined impinging air jet”, Experimental Thermal and Fluid Science, Vol. 13, pp. 71-80, 1996.
S. Ashforth-Frost, K. Jambunathan and C.F. Whitney, “Velocity and turbulence characteristics of a semiconfined orthogonally impinging slot jet”, Experimental Thermal and Fluid Science, Vol. 14, pp. 60-67, 1997.
L.A. Brignoni and S.V. Garimella, “Effects of nozzle-inlet chamfering on pressure drop and heat transfer in confined air jet impingement”, International Journal of Heat and Mass Transfer, Vol. 43, pp. 1133-1139, 2000.
J. Lee and S.J. Lee, “The effect of nozzle aspect ratio on stagnation region heat transfer characteristics of elliptic impinging jet”, International Journal of Heat and Mass Transfer, Vol. 43, pp. 555-575, 2000.
J. Lee and S.J. Lee, “The effect of nozzle configuration on stagnation region heat transfer enhancement of axisymmetric jet impingement”, International Journal of Heat and Mass Transfer, Vol. 43, pp. 3497-3509, 2000.
N. Gao, H. Sun and D. Ewing, “Heat transfer to impinging round jets with triangular tabs”, International Journal of Heat and Mass Transfer Vol. 46, pp. 2557-2569, 2003.
D.W. Zhou and S.J. Lee, “Heat transfer enhancement of impinging jets using mesh screens”, International Journal of Heat and Mass Transfer Vol. 47, pp. 2097-2108, 2004.
H.M. Hofmann, M. Kind and H. Martin, “Measurements on steady state heat transfer and flow structure and new correlations for heat and mass transfer in submerged impinging jets”, International Journal of Heat and Mass Transfer, Vol. 50, pp. 3957-3965, 2007.
D.W. Zhou and S.J. Lee, “Forced convective heat transfer with impinging rectangular jets”, International Journal of Heat and Mass Transfer Vol. 50, pp. 1916-1926, 2007.
P. Gulati, V. Katti and S.V. Prabhu, “Influence of the shape of the nozzle on local heat transfer distribution between smooth flat surface and impinging air jet”, International Journal of Thermal Sciences, Vol. 48, pp. 602-617, 2009.
R.H. Martin and J.M. Buchlin, “Jet impingement heat transfer from lobed nozzles”, International Journal of Thermal Sciences, Vol. 50, pp. 1199-1206, 2011.
H.S. Zhen, C.W. Leung and C.S. Cheung, “Heat transfer characteristics of an impinging premixed annular flame jet”, Applied Thermal Engineering, Vol. 36, pp. 386-392, 2012.
M. Attalla and M. Salem, “Effect of nozzle geometry on heat transfer characteristics from a single circular air jet”, Applied Thermal Engineering, Vol. 51, pp. 723-733 2013.
R. Vinze, S. Chandel, M.D. Limaye and S.V. Prabhu, “Local heat transfer distribution between smooth flat surface and impinging incompressible air jet from a chevron nozzle, Experimental Thermal and Fluid Science, Vol. 78, pp. 124-136, 2016.
H.C. Meena, S.A. Reodikar, R. Vinze and S.V. Prabhu, “Influence of the shape of the orifice on the local heat transfer distribution between smooth flat surface and impinging incompressible air jet”, Experimental Thermal and Fluid Science, Vol. 70, pp. 292-306, 2016.
X.T. Trinh, M. Fénot and E. Dorignac, “The effect of nozzle geometry on local convective heat transfer to unconfined impinging air jets”, Experimental Thermal and Fluid Science, Vol. 70, pp. 1-16, 2016.
L. Huang and M. S. El-Genk, “Heat transfer and flow visualization experiments of swirling, multi-channel, and conventional impinging jets”, International Journal of Heat and Mass Transfer, Vol. 41, pp. 583-600, 1998.
D.H. Lee, S.E. Won, Y.T. Kim and Y.S. Chung, “Turbulent heat transfer from a flat surface to a swirling round impinging jet”, International Journal of Heat and Mass Transfer, Vol. 45, pp. 223-227, 2002.
M.Y. Wen and K.J. Jang, “An impingement cooling on a flat surface by using circular jet with longitudinal swirling strips”, International Journal of Heat and Mass Transfer, Vol. 46, pp. 4657-4667, 2003.
M.Y. Wen, “Flow structures and heat transfer of swirling jet impinging on a flat surface with micro-vibrations”, International Journal of Heat and Mass Transfer, Vol. 48, pp. 545-560, 2005.
M. Senda, K. Inaoka, D. Toyoda, and S. Sato, “Heat transfer and fluid flow characteristics in a swirling impinging jet”, Heat Transfer-Asian Research, Vol. 34, pp. 324-335, 2005.
Z.X. Yuan, Y.Y. Chen, J.G. Jiang, C.F. Ma, “Swirling effect of jet impingement on heat transfer from a flat surface to CO2 stream”, Experimental Thermal and Fluid Science, Vol. 31, pp. 55-60, 2006.
K. Bakirci and K. Bilen, “Visualization of heat transfer for impinging swirl flow”, Experimental Thermal and Fluid Science, Vol. 32, pp. 182-191, 2007.
S.V. Alekseenko, A.V. Bilsky, V.M. Dulin, D.M. Markovich, “Experimental study of an impinging jet with different swirl rates”, International Journal of Heat and Fluid Flow, Vol. 28, pp. 1340-1359, 2007.
C. Kinsella, B. Donnelly, T.S. O’Donovan and D. B. Murray, “Heat transfer enhancement from a horizontal surface by impinging swirling jets”, 5th European Thermal-Sciences Conference, The Netherlands, 2008.
H.Q. Yang, T. Kim, T.J. Lu, and K. Ichimiya, “Flow structure, wall pressure and heat transfer characteristics of impinging annular jet with/without steady swirling”, International Journal of Heat and Mass Transfer, Vol. 53, pp. 4092-4100, 2010.
K. Nanan, K. Wongcharee, C. Nuntadusit and S. Eiamsa-ard, “Forced convective heat transfer by swirling impinging jets issuing from nozzles equipped with twisted tapes”, International Communications in Heat and Mass Transfer Vol. 39, pp. 844-852, 2012.
A. Ianiro and G. Cardone, “Heat transfer rate and uniformity in multichannel swirling impinging jets”, Applied Thermal Engineering, Vol. 49, pp. 89-98, 2012.
C. Nuntadusit, M. Wae-hayee, A. Bunyajitradulya and S. Eiamsa-ard, “Visualization of flow and heat transfer characteristics for swirling impinging jet” International Communications in Heat and Mass Transfer, Vol. 39, pp. 640-648, 2012.
M. Fénot, E. Dorignac, and G. Lalizel, “Heat transfer and flow structure of a multichannel impinging jet”, International Journal of Thermal Sciences, Vol. 90, pp. 323-338, 2015.
V. Hindasageri, R.P. Vedula and S.V. Prabhu, “Heat transfer distribution of swirling flame jet impinging on a flat plate using twisted tapes”, International Journal of Heat and Mass Transfer, Vol. 91, pp. 1128-1139, 2015.
S. Eiamsa-ard, K. Nanan and K. Wongcharee, Heat transfer visualization of co/counter-dual swirling impinging jets by thermochromic liquid crystal method”, International Journal of Heat and Mass Transfer, Vol. 86, pp. 600-621, 2015.
Y. Amini, M. Mokhtari, M. Haghshenasfard and M.B. Gerdroodbary, “Heat transfer of swirling impinging jets ejected from nozzles with twisted tapes utilizing CFD technique”, Case Studies in Thermal Engineering, Vol. 6, pp. 104-115, 2015.
Z.U. Ahmed, Y.M. Al-Abdeli and F.G. Guzzomi, “Flow field and thermal behaviour in swirling and non-swirling turbulent impinging jets”, International Journal of Thermal Sciences, Vol. 114, pp. 241-256, 2017.
S.S Kumar, V. Hindasageri and S.V. Prabhu, “Local heat transfer distribution on a flat plate impinged by a swirling jet generated by a twisted tape”, International Journal of Thermal Sciences, Vol. 111 pp. 351-368, 2017.
L. Xu, J. Lan, Y. Ma, J. Gao and Y. Li, “Numerical study on heat transfer by swirling impinging jets issuing from a screw-thread nozzle”, International Journal of Heat and Mass Transfer, Vol. 115 pp. 232-237, 2017.
S. Eiamsa-ard, C. Nuntadusit, K. Wongcharee and V. Chuwattanakul, “An impingement cooling using swirling jets induced by helical rod swirl generators”, International Journal of Turbo and Jet Engines, Vol. 35, pp. 241-250, 2018.
B. Markal, “Experimental investigation of heat transfer characteristics and wall pressure distribution of swirling coaxial confined impinging air jets”, International Journal of Heat and Mass Transfer, Vol. 124, pp. 517-532, 2018.
N. Uddin, B. Weigand and B.A. Younis, “Comparative study on heat transfer enhancement by turbulent impinging jet under conditions of swirl, active excitations and passive excitations”, International Communications in Heat and Mass Transfer, Vol. 100, pp. 35-41, 2019.
M. Ikhlaq, Y.M. Al-Abdeli and M. Khiadani, “Transient heat transfer characteristics of swirling and non-swirling turbulent impinging jets”, Experimental Thermal and Fluid Science, Vol. 109, 109917, 2019.