Flow Analysis for Determining Design Parameters of Dipping Tanks in Continuous Latex-Gloves Production Lines Using Computational Fluid Dynamics

Article Sidebar

PDF
Published: Feb 23, 2023
DOI: https://doi.org/10.14416/j.asep.2022.04.002
Keywords:
Latex gloves Latex dipping process Computational fluid dynamics Simulations, Optimization

Main Article Content

Worrapol Koranuntachai
Development of Machinery and Industrial Equipment Research Center (DMIE), Department of Mechanical and Aerospace Engineering, King Mongkut’s University of Technology North Bangkok, Bangkok, Thailand
Tonkid Chantrasmi
Development of Machinery and Industrial Equipment Research Center (DMIE), Department of Mechanical and Aerospace Engineering, King Mongkut’s University of Technology North Bangkok, Bangkok, Thailand
Udomkiat Nontakaew
Development of Machinery and Industrial Equipment Research Center (DMIE), Department of Mechanical and Aerospace Engineering, King Mongkut’s University of Technology North Bangkok, Bangkok, Thailand

Abstract

In continuous latex-gloves production lines, ceramic formers are lowered into open-channel, latex-dipping tanks. These tanks are known to be critical to the final product quality, so they should be designed carefully. This paper presents a method to determine the optimal design and operating parameters of an island-type, latex-dipping tank. Typically, the conveyor speed is treated a given parameter. The length and the height of the tank can be trivially obtained and considered fixed in this work. The tank width and the driving pressure gradient, on the other hand, are complicated to choose appropriately. This study proposes a systematic approach to obtain the optimal values of these two parameters at each conveyor speed. The analysis consists of three main parts. First, all possible combinations of the parameters are determined by requiring the flow to be laminar and steady. In the second step, Computational Fluid Dynamics (CFD) simulations are conducted to find the combination with the lowest maximum shear stress on the former. Finally, the results from the first two parts are logically combined to give the recommended parameter ranges. One of the practical benefits of the proposed method is that it can be used to find the optimal latex flow rate in the dipping tank of an existing production line. For example, a latex glove production line with the conveyor speed of 0.3 m/s and the tank width of 40 cm should adjust the flow inside the latex dipping tanks to be around 1,940–2,140 L/min.

Article Details

How to Cite
Koranuntachai, W., Chantrasmi, T., & Nontakaew, U. (2023). Flow Analysis for Determining Design Parameters of Dipping Tanks in Continuous Latex-Gloves Production Lines Using Computational Fluid Dynamics. Applied Science and Engineering Progress, 16(2), 5851. https://doi.org/10.14416/j.asep.2022.04.002
Issue
Vol. 16 No. 2 (2023)
Section
Research Articles

References

D. C. Blackley, Polymer Latices Science and Technology Volume 3: Applications of Latices, 2nd ed. New York: Springer Science, 1997.

P. Cacioli, “Introduction to latex and the rubber industry,” Revue Francaise d'Allergologie et d'Immunologie Clinique, vol. 37, no. 8, pp. 1173–1176, 1997.

E. Yip and P. Cacioli, “The manufacture of gloves from natural rubber latex,” Journal of Allergy and Clinical Immunology, vol. 110, no. 2, pp. S3–S14, 2002.

M. C. Ng, H. Ab-Samat, and S. Kamaruddin, “Reduction of defects in latex dipping production: A case study in a malaysian company for process improvement,” The International Journal of Engineering and Science, vol. 2, no. 6, pp. 2319–1813, 2013.

N. Abdullah and A.-H. M. Yatim, “Film formation in rubber gloves,” MRB Rubber Technology Developments, vol. 14, no. 1, pp. 15–20, 2014.

D. Hill, The Science and Technology of Latex Dipping. United Kingdom: Smithers Rapra, 2018.

B. A. M. Sabri, N. H. M. Radzi, F. Z. A. Hadi, and I. H. Ismail, “Feasibility of using latex examination gloves as dental dam: A tensile strength study,” Compendium of Oral Science, vol. 1, pp. 6–13, 2015.

S. Jariyapongpaiboon, O. Pinprayoon, and O. Onjun, “A comparison study of physical properties of dental dam, latex examination gloves and nitrile examination gloves: Tensile strength, elongation and tear strength properties,” Journal of the Department of Medical Services, vol. 45, no. 3, pp. 82–89, 2020.

Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers, ASTM Standard D412, 2002.

Standard Specification for Rubber Examination Gloves, ASTM Standard D3578, 2002.

Standard Test Method for Detection of Holes in Medical Gloves, ASTM Standard D5151, 2003.

P. Jirasukprasert, J. A. Garza-Reyes, V. Kumar, and M. K. Lim, “A six sigma and dmaic application for the reduction of defects in a rubber gloves manufacturing process,” International Journal of Lean Six Sigma, vol. 5, no. 1, pp. 2–22, 2015.

K. K. Sasidharan, R. Joseph, G. Rajammal, P. Viswanatha Pillai, and K. S. Gopalakrishnan, “Studies on the dipping characteristics of RVNRL and NR latex compounds,” Journal of Applied Polymer Science, vol. 81, no. 13, pp. 3141–3148, 2001.

W. Jitwiriya, T. Chantrasmi, U. Nontakaew, and P. Yongyingsakthavorn, “Heat loss analysis of continuous drying oven with outside conveyor chain,” Applied Science and Engineering Progress, vol. 14, no. 3, pp. 387–396, 2021, doi: 10.14416/j.asep.2020.07.003.

S. Lakkum, P. Ninpetch, N. Phophichit, P. Kowitwarangkul, A. Tawai, and S. Otarawanna, “Numerical and physical investigation of the mixing process in gas stirred ladle system,” Applied Science and Engineering Progress, vol. 14, no. 3, pp. 447–459, 2021, doi: 10.14416/ j.asep.2020.07.001.

T. Kuljitjuawong, D. Kositgittiwong, C. Ekkawatpanit, and R. Sukjan, “Comparison of the flow behaviours of physical and numerical models on a stepped spillway,” Applied Science and Engineering Progress, vol. 14, no. 2, pp. 165– 174, 2021, doi: 10.14416/j.asep.2020.05.004.

B. N. Rajani, A. Kandasamy, and S. Majumdar, “Numerical simulation of laminar flow past a circular cylinder,” Applied Mathematical Modelling, vol. 33, no. 3, pp. 1228–1247, 2009.

R. Gautier, D. Biau, and E. Lamballais, “A reference solution of the flow over a circular cylinder at Re=40,” Computers and Fluids, vol. 75, pp. 103–111, 2013.

B. Fornberg, “A numerical study of steady viscous flow past a circular cylinder,” Journal of Fluid Mechanics, vol. 98, no. 4, pp. 819–855, 1980.

S. Sen, S. Mittal, G. Biswas, U. Pradesh, and W. Bengal, “Numerical simulation of steady flow past a circular cylinder,” presented at the International Conference on Fluid Mechanics and Fluid Power, Chennai, India, Dec 16–18, 2010.

S. Singha and K. P. Sinhamahapatra, “Flow past a circular cylinder between parallel walls at low Reynolds numbers,” Ocean Engineering, vol. 37, no. 8–9, pp. 757–769, 2010.

M. Tachibana and Y. Iemoto, “Steady flow around, and drag on a circular cylinder moving at low speeds in a viscous liquid between two parallel planes,” Fluid Dynamics Research, vol. 2, no. 2, pp. 125–137, 1987.

L. Zovatto and G. Pedrizzetti, “Flow about a circular cylinder between parallel walls,” Journal of Fluid Mechanics, vol. 440, pp. 1–25, 2001.

J. Chakraborty, N. Verma, and R. P. Chhabra, “Wall effects in flow past a circular cylinder in a plane channel: A numerical study,” Chemical Engineering and Processing: Process Intensification, vol. 43, no. 12, pp. 1529–1537, 2004.

D. G. Crowdy, “Uniform flow past a periodic array of cylinders,” European Journal of Mechanics B/Fluids, vol. 56, pp. 120–129, 2016.

C. Pozrikidis, “Boundary conditions for shear flow past a permeable interface modeled as an array of cylinders,” Computers and Fluids, vol. 33, no. 1, pp. 1–17, 2004.

B. Andersson, R. Andersson, L. Hakansson, M. Mortensen, and B. G. M. van Wachem, Computational Fluid Dynamics for Engineers. United Kingdom: Cambridge University Press, 2012.

J. F. Wendt, Computational Fluid Dynamics: An Introduction, 3rd ed. Berlin, Germany: Springer- Verlag, 2009.

A. D. T. Gorton, “Latex dipping I. relationship between dwell time, latex compound viscosity and deposit thickness,” Journal of Rubber Research Institute of Malaya, vol. 20, no. 1, pp. 27–35, 1966.

C. Chaowanich and N. Nitthi-Uthai, “Effect of maturation on properties of latex compounds,” Prince of Songkla University, Songkla, 2006.

Y. A. Çengel and J. M. Cimbala, Fluid Mechanics: Fundamentals and Applications. New York: McGraw-Hill Education, 2006.

B. R. Munson, T. H. Okiishi, W. W. Huebsch, and A. P. Rothmayer, Fundamentals of Fluid Mechanics, 7th ed. New Jersey: John Wiley & Sons, 2013.

M. H. Chaudhry, Open-Channel Flow, 2nd ed. New York: Springer Science, 2008.

G. E. Moglen, Fundamentals of Open Channel Flow. Florida: CRC Press, 2013.

J. P. Holman, Heat Transfer, 10th ed. New York: McGraw-Hill Education, 2009.

T. Von Karman, Aerodynamics. New York: McGraw-Hill, 1964.

H. Schlichting, Boundary-layer Theory, 7th ed. New York: McGraw-Hill Book, 1979.

A. A. Johnson, T. E. Tezduyar, and J. Liou, “Numerical simulation of flows past periodic arrays of cylinders,” Computational Mechanics, vol. 11, no. 5–6, pp. 371–383, 1993.

A. Quarteroni, “The finite volume method,” in Numerical Models for Differential Problems. New York: Springer Publishing, 2014.

R. Eymard, E. Normale, and U. De Provence, Handbook of Numerical Analysis. Amsterdam, Netherlands: Elsevier Science, 2000.

H. K. Versteeg and W. Malalasekera, An Introduction to Computational Fluid Dynamics, 2nd ed. New York: Pearson Education Limited, 2007.

B. Vink, J. Schot, G. Vaz, and S. Toxopeus, “A verification and validation study of CFD simulations for the flow around a tug,” presented at the 20th Numerical Towing Tank Symposium, Wageningen, Netherlands, Oct. 1–3, 2017.

S. Mansor, N. A. R. N. Mohd, and C. W. Chung, “Validation of CFD modeling and simulation of a simplified automotive model,” Applied Mechanics and Materials, vol. 735, pp. 319–325, 2015.